Estimate Impedance from the Finished Geometry
Use this trace impedance calculator for a first-pass estimate of single-ended surface microstrip or symmetric stripline impedance. Enter the finished conductor geometry and dielectric constant, or solve for a starting width at a specified target.
Use the result to prepare a stack-up discussion. We review the production geometry, material properties and required impedance verification before fabrication.
Calculate Impedance or Solve for Width
Surface microstrip
H is the dielectric gap from the bottom of the trace to the reference plane.
Enter the finished geometry and calculate.
Choose the Geometry That Matches Your Layer
Surface microstrip: a surface trace above one reference plane, with air above the conductor. H is the dielectric distance from the trace bottom to the plane.
Symmetric stripline: a trace centered between two reference planes in the same dielectric. H is the gap from each trace face to the adjacent plane, so the plane separation is B = 2H + T.
This worksheet covers single-ended structures. Differential pairs, asymmetric or embedded structures and coplanar geometry require their corresponding models.
Enter Stack-Up Values with a Clear Basis
- W: finished trace width, with the conductor-width convention confirmed for manufacturing review.
- T: finished copper thickness; enter a physical thickness rather than a copper-weight label.
- H: pressed dielectric spacing to the reference plane, not the total board thickness.
- Dk: relative dielectric constant for the selected material and intended application. The initial value is an example, not a material specification.
- Target impedance: the required single-ended value in ohms when solving for width.
Understand the Calculation Model
The tool uses closed-form transmission-line approximations documented in Analog Devices MT-094 and Texas Instruments AN-1469. It is not an electromagnetic field solver.
Microstrip: Z₀ = 87 / √(Dk + 1.41) × ln[5.98H / (0.8W + T)].
Symmetric stripline: Z₀ = 60 / √Dk × ln[1.9(2H + T) / (0.8W + T)].
This worksheet restricts inputs to 0.1 ≤ W/H ≤ 2, T/H ≤ 0.25 and 1 ≤ Dk ≤ 20. These screening limits do not guarantee model accuracy. Solder mask, copper roughness, frequency dispersion, nearby traces and discontinuities are not modeled.
Take the Estimate into Manufacturing Review
Provide the selected geometry, target and tolerance, routing layer, reference planes and proposed stack-up. Include the dielectric material, finished copper and any restrictions on changes to width or spacing.
Our controlled impedance PCB manufacturing service reviews the production construction and agreed verification. The existing trace width calculator addresses current and temperature rise, which is a different design question.
Trace Impedance Calculator FAQs
Compare the line geometry, finished copper, pressed dielectric spacing, Dk and modeling assumptions. A field solver may include solder mask, conductor shape or other effects omitted here. Send the input summary and target tolerance so the production stack-up and measurement plan can be reconciled.
No. For surface microstrip, use the dielectric gap from the bottom of the trace to its reference plane. For symmetric stripline, use the equal dielectric gap on each side of the conductor. If you only know the full board thickness, request the layer stack-up before calculating.
Use the material supplier information appropriate to the laminate, frequency and construction, with the test method understood. Do not assume every FR-4 grade has the initial example value. For a manufacturing decision, identify the exact material and ask us to confirm the modeling basis.
Check the units and geometry first. If the width is outside this worksheet’s screened range, use an appropriate field solver. If a positive width is calculated but cannot be manufactured, review dielectric spacing, material or layer arrangement while preserving the electrical requirements.
Not directly. This calculator estimates single-ended impedance and does not include coupling between two traces. Provide the pair geometry, edge-to-edge spacing, target differential impedance and stack-up for a coupled-line calculation; do not simply double this result.
No. The output is a nominal model estimate, not a board measurement. Specify the target, tolerance, test structures and required report with the fabrication order. Production geometry and the agreed impedance test must be reviewed separately.
Review Your Impedance Stack-Up with Us
Send your calculator inputs, target impedance and board stack-up. We will review the finished geometry, material requirements and verification scope for your PCB.
