Halogen-Free PCB Manufacturing

Halogen-Free PCB Manufacturing Options

Need a PCB built with halogen-free materials? We help select laminates and prepregs based on the required stack-up, thermal performance and electrical properties.

We support prototype builds and production runs. Send your material requirements, design files and quantity for a manufacturing review.

Black solder-mask PCB with gold-finished pads and dense component footprints

Halogen-Free Requirements and Material Scope

The commonly used limits in IEC 61249-2-21 apply to bromine and chlorine in the specified material. Other halogens may be subject to separate customer requirements. Confirm the applicable standard and whether the requirement covers the laminate or the finished PCB.

Br

Bromine (Br)

< 900 ppm by weight

Cl

Chlorine (Cl)

< 900 ppm by weight

Br + Cl

Combined Br + Cl

< 1,500 ppm by weight

Halogen-Free PCB Material Options

We compare laminate grades using published manufacturer data. The Tg values below are nominal material figures, not test results from finished PCBs.

Manufacturer / Grade

Nominal Tg u00b7 Typical selection

Ventec VT-441

150u00b0C u00b7 General halogen-free FR-4

Ventec VT-447

175u00b0C u00b7 Higher-Tg FR-4

Ventec VT-464G

200u00b0C u00b7 Low-loss, high-speed designs

Isola TerraGreen 400G2

200u00b0C u00b7 Very low loss, high-speed designs

TerraGreen 400G2 is subject to L2 glass availability. We confirm current material availability, prepreg compatibility, copper foil options and Dk/Df test conditions for each stack-up.

Halogen-Free PCB Manufacturing Capabilities

Available options depend on the selected material and board construction. We review the laminate grade, copper weight and process limits together for each design.

Board construction

Rigid multilayer PCB and HDI designs; construction selected by stack-up

Layer count

Prototype to advanced multilayer builds; up to 40 layers, subject to design review

Copper weight

0.5 oz, 1 oz, 2 oz and heavier copper, subject to design review

Finished thickness

Selected by material system, layer count and construction

Thermal properties

Tg, Td, CTE and T260/T288 by laminate grade

Electrical properties

Dk and Df by material, test frequency and method

Reliability properties

CTI rating and CAF resistance, where required by the material and application

Surface finishes

ENIG, OSP, lead-free HASL and other project-specified options

Fabrication checks

DFM, dimensional inspection and bare-board electrical testing

Documentation

Manufacturer datasheets and relevant material declarations by request

Green printed circuit board with dense component placement, fine traces and mounting holes

Material Selection and Stack-Up Design

We review laminate and prepreg compatibility, copper weight, dielectric thickness and lamination requirements before production.

For high-speed signals, we compare Dk and Df at the relevant frequency. For thermal requirements, we review Tg, decomposition temperature and expansion behavior.

Quality Checks and Material Documentation

Material Traceability

We check the selected laminate grade against the relevant supplier documentation.

Manufacturing Inspection

We inspect board dimensions, finished holes and surface finish, and test for opens and shorts.

Project-Specific Compliance Testing

We confirm the test scope, method and acceptance criteria when project-specific testing is required.

A material datasheet or supplier declaration does not by itself establish compliance of the finished PCB.

Files Required for a Halogen-Free PCB Quote

Send your available design data. We will identify any missing material or compliance details before preparing a quotation.

  • Gerber or ODB++ and NC Drill files
  • Board outline and layer stack-up
  • Preferred laminate and prepreg grades
  • Halogen-free standard and required declaration scope
  • Copper thickness and surface finish
  • Quantity, delivery target and special tests
Green printed circuit board with exposed gold-finished pads, fine traces and component footprints

Frequently Asked Questions

The specified material must meet the applicable bromine and chlorine limits. Other halogens may be subject to separate customer requirements. Confirm whether the requirement covers the laminate only or the finished PCB.

No. Halogen limits and RoHS restricted-substance requirements are different criteria. A halogen-free material declaration does not establish RoHS compliance.

Options include Ventec VT-441, VT-447 and VT-464G, and Isola TerraGreen 400G2. We check current availability and stack-up compatibility for each project.

Yes. ENIG and OSP are available options where specified. We select the finish based on the PCB design, assembly method and project requirements.

Yes. We review the laminate, prepreg, layer structure and fabrication process before confirming suitability.

Send Gerber or ODB++ files, NC Drill data, the stack-up, preferred material, required standard, surface finish and quantity.

Need a Halogen-Free PCB Quote?

Send your PCB design, preferred material and halogen-free requirements. We will review the build and quotation details.