PCB Drilling Services

Holes for Electrical Connections and Mechanical Fit

We provide PCB drilling services for plated connections, component leads, mounting holes and via structures. We review the finished hole size, location, plating requirement and layer span with your board construction.

Send your fabrication data, drill files, stack-up and quantity. Identify connector-fit requirements, press-fit holes and other critical features so we can plan the drilling and inspection requirements before production.

Specify Plated and Non-Plated Holes Clearly

Plated through holes use a conductive barrel to connect the required copper layers. Non-plated holes provide mechanical openings without a plated barrel, such as mounting or alignment holes.

Mark each hole group as plated or non-plated in the drill data and fabrication drawing. Provide separate files where possible, or a clear tool table that identifies both types without relying on pad appearance alone.

Cross-section diagrams comparing a plated through hole with a copper barrel and a non-plated mechanical hole

Drilling Capabilities and Hole Requirements

FeatureCapability or requirementDesign information
Mechanical finished holeMinimum diameter: 0.15 mmReview the hole size with board thickness, material and required plating.
PTH diameter tolerance±0.08 mmSpecify the finished opening after plating and relevant finishing operations.
NPTH diameter tolerance±0.05 mmIdentify mounting, locating and other fit-critical holes in the drawing.
Hole positionPosition requirements reviewed against the specified datum system.Distinguish coordinate tolerances from a diametral true-position tolerance.
Laser microviasBlind microvias reviewed with the HDI build-up.Provide dielectric depth, layer span, target pad and opening geometry.
Press-fit and special holesHole geometry and inspection planned to the component requirements.Provide the connector drawing, finished size range, plating and surface-finish requirements.

Use Finished Hole Sizes in the Fabrication Requirements

Cross-section diagrams showing a production drill opening before plating and the smaller finished opening after copper plating

For a plated hole, the production drill opening is larger than the finished opening because material is added to the hole wall. State the required finished size and tolerance; we select the production tool and allowance for the manufacturing process.

If your export uses tool sizes rather than finished sizes, identify that convention explicitly. Keep the drill file, hole table and fabrication notes consistent so a plating allowance is not applied twice.

Match the Drilling Method to the Stack-Up

Mechanical drilling forms through holes and selected depth-controlled structures. Laser drilling forms small blind vias in an appropriate build-up, with the via depth and copper targets considered together.

For a through-hole aspect-ratio requirement, identify the thickness and hole-diameter basis used in the calculation. For blind microvias, review the local dielectric depth and opening geometry instead of applying the full board thickness.

Our HDI PCB manufacturing service covers build-up structures that require small blind vias and sequential processing.

Control Hole Location and Prepare the Walls for Plating

We plan drilling around the material, stack-up, hole size and registration requirements. Entry and backing materials, tool condition and drilling conditions affect hole location, burr formation and wall quality.

For holes that require metallization, the manufacturing route includes suitable hole-wall preparation before plating. Inspection addresses finished size, position and the specified construction requirements, with microsection checks where required.

Top-view diagrams comparing a centered drilled hole and an offset drilled hole within a copper pad

Review Clearances and Special Features

  • Hole-to-hole spacing: identify the edge-to-edge measurement basis and allow for the production tool sizes.
  • Copper clearance: define isolation to unconnected copper and the required annular ring at connected layers.
  • Mounting and press-fit holes: provide datums, mating-part dimensions and the finished fit requirements.
  • Slots and cut-outs: supply the intended geometry and plating status rather than a chain of overlapping drill hits.
  • Blind, buried and backdrilled features: identify the layer span, entry side and depth or protected-layer requirements.

Files for a PCB Drilling Review

  • Gerber or ODB++ data with the approved board revision
  • NC drill files with units, coordinate format and origin identified
  • PTH and NPTH identification, tool table and hole counts
  • Fabrication drawing with finished diameters, tolerances and location datums
  • Stack-up, board thickness and any blind or buried via layer spans
  • Connector drawings and special fit or inspection requirements

Drilling is coordinated with our PCB fabrication services. For critical hole groups, identify any drawing or data approval needed before production.

PCB Drilling FAQs

State the finished hole diameter and tolerance in the fabrication requirements. Identify whether the NC file uses finished sizes or production tool sizes. We reconcile that convention with the hole table before selecting the drilling allowance, so the plated opening is not reduced by a duplicated allowance.

Separate PTH and NPTH files help avoid ambiguity. If you use one file, identify each tool as plated or non-plated and match it to the fabrication drawing. Clarify conflicting hole notes before manufacturing rather than leaving the plating status to be inferred from the pads.

Send the connector drawing, finished hole range, pin geometry and required plating and surface finish. Identify the relevant datums and hole group in your fabrication drawing. A press-fit opening needs its specified dimensional and wall requirements; a general mounting-hole tolerance may not provide the required fit.

Check that the drill and artwork files share the same units, coordinate format, origin, orientation and revision. Compare known reference holes before changing any offsets. If the files agree but the drilled holes on a manufactured board are displaced, record the measured locations and datums so we can investigate registration against the approved drawing.

Provide the hole size, board thickness, material and layer span for review. If the construction is unsuitable, compare a larger through hole, a thinner stack-up or a blind or buried via structure that reduces the drilled depth. Any change must also preserve the required electrical connections and component fit.

Check the finished opening and condition against the drawing, then identify and hold the affected boards. We review whether the cause is size, plating, residue or an edge defect before agreeing on an action. Do not redrill a plated hole without an approved repair process, because this can damage the barrel; verify any authorized correction before release.

Discuss Your PCB Hole Requirements

Send your drill files, fabrication drawing and stack-up. We will review the hole types, finished dimensions and critical fit requirements with your PCB manufacturing order.