ENEPIG PCB Finish

Nickel, palladium and gold finishes for soldering and specified wire bonding.

ENEPIG for Soldering and Wire-Bond Pads

We provide ENEPIG PCB finishes for prototype and production orders. Electroless nickel, electroless palladium and immersion gold form a flat surface for soldering and specified wire-bonding applications.

Send your board files, finish requirements and bonding details. We review the three coating layers alongside the pad functions and assembly process before confirming the manufacturing specification.

Flat gold-finished pads and a fine-pitch component footprint on a bare PCB.

Three Layers with Different Functions

ENEPIG adds a palladium layer to the nickel-and-gold structure. Specify and verify nickel, palladium and gold separately.

Electroless Nickel

Nickel acts as a diffusion barrier over the copper. Its thickness and deposit condition are part of the coating specification.

Electroless Palladium

Palladium sits between nickel and gold. It helps protect the nickel during gold deposition and supports the coating system used for qualified wire bonding.

Immersion Gold

A thin gold layer protects the surface before assembly. Its thickness must suit the selected coating process and the intended soldering or bonding use.

Fine gold wires connecting a bare chip to gold bond pads on a PCB.

Define the Wire-Bonding Requirements

For wire-bonded designs, identify the bond pads and provide the wire material, wire diameter and bonding method. Include the expected thermal exposure before bonding and any pad-cleanliness requirements.

Gold and aluminum wire bonding require a coating and process that have been qualified for the actual assembly. We review the requested bond-pull or other applicable test method, sampling and acceptance criteria with your team.

Keep thickness verification separate from bond-performance testing. A conforming thickness result alone does not qualify the bonding process.

Put the Finish Requirements on the Drawing

Choose the coating specification for the actual assembly. We confirm the requested thickness ranges and inspection scope before production.

Nickel, Palladium and Gold

State the required thickness range for each layer, including units and any local minimum or maximum limits. Avoid specifying only a total coating thickness.

Standard and Revision

If IPC-4556 is required, identify the applicable revision or amendment on the drawing and order. Include any tighter customer requirements so the acceptance basis is clear.

Measurement Locations

Identify critical pads and the required sampling. X-ray fluorescence (XRF) can measure the coating layers when the calibration and measurement method suit the layer system and pad geometry.

Application and Acceptance

Mark solder pads and bond pads by function. Define solderability and bonding verification separately from the coating-thickness report.

Plan Soldering and Bonding on the Same Board

A single board can contain solder lands and wire-bond pads. We review the finish against both uses, including pad dimensions, solder-mask openings and the order of assembly operations.

Provide the solder alloy, reflow sequence, cleaning steps and details of any later bonding operation. This helps us review the surface condition required at each stage of your PCB assembly process.

For BGA, QFN and other fine-pitch layouts, the flat finish is one part of the assembly design. Pad geometry, via treatment and solder-paste printing also need to suit the package.

Round solder pads and narrow wire-bond pads on a bare green PCB.

Select the Finish by Pad Function

Compare the assembly and contact requirements before choosing a gold finish. Appearance alone does not establish suitability.

ENEPIG and ENIG

ENEPIG adds palladium between nickel and gold. Consider it when the design needs a qualified wire-bondable surface alongside solderable pads. ENIG is an option when it meets the specified soldering and interface requirements.

ENEPIG and Hard Gold

Electroplated hard gold serves specified wear contacts such as repeatedly mated edge fingers. Select ENEPIG for its qualified assembly functions rather than treating it as a direct substitute for a hard-gold contact specification.

RF and Fine-Line Designs

ENEPIG still includes nickel. Provide any RF loss restrictions and critical exposed-feature dimensions so the coating can be considered in the electrical and manufacturing review.

Verify the Coating and Its Intended Use

Agree on inspection and test requirements with the order. Thickness measurement, solderability testing and bonding evaluation answer different questions.

Coating and Surface Condition

Review thickness, coverage and visible surface defects against the agreed criteria. Palladium helps protect nickel during gold deposition. Control of the coating process is still needed to address nickel corrosion.

Solderability

If solderability testing is required, specify the test method, conditioning and acceptance criteria. Storage, handling and assembly heat exposure need to be included in the plan.

Bonding Verification

Define the wire and bonding process with the applicable acceptance test. Agree on qualification samples and production checks before release.

Packaging and Records

Specify protective packaging, board or lot identification and the reports required with the order. Follow the supplied storage and handling instructions to protect the pads before assembly.

Files for an ENEPIG PCB Quote

Send the current files and identify any soldering, bonding or contact requirements that affect finish selection.

  • Gerber or ODB++ data, drill files and fabrication drawing
  • Board dimensions, layer count, material and finished thickness
  • Separate nickel, palladium and gold thickness requirements
  • Standard revision, critical pad locations and sampling requirements
  • Bond-pad drawing, wire material, diameter and bonding method
  • Assembly thermal exposure, cleaning and handling requirements
  • Order quantity, required tests and report format

See our PCB fabrication services for the wider manufacturing scope and our lead-free PCB manufacturing for other finish options.

ENEPIG PCB Finish FAQs

Treat this as a specification change, not a direct substitution. Have the design and assembly teams approve the new finish, update the drawing revision, and confirm any soldering or bonding qualification needed. Send the revised requirements so we can review the coating specification and quotation before production.

Add the required nickel, palladium and gold thickness limits separately, with units and the applicable standard revision. Identify critical pads, measurement locations and required reports. If those values have not been selected, send the assembly requirements and any bonding specification so we can review the missing details with your team.

Yes, with a coating and assembly sequence qualified for both operations. Mark the solder pads and bond pads, then provide the solder alloy, reflow sequence, cleaning steps, wire material and bonding method. Confirm the surface condition needed at the bonding stage, including any prior thermal exposure, before approving the production plan.

First confirm which pads were measured and whether the report covers nickel, palladium and gold separately. Compare the failed pads with the specified surface condition, handling and thermal history, then review the wire material, bonding settings and failure location with the assembly team. Share the thickness data, pad photographs and bond-test results so the coating and bonding process can be investigated together.

Keep boards in their supplied protective packaging and follow the storage instructions provided for the order. Avoid touching bond pads and record when packaging is opened. If boards have been stored beyond the specified period or exposed to contamination, confirm any cleaning, baking or verification procedure with the board supplier and bonding team before use.

Yes. Send the available manufacturing files, quantity and known soldering or bonding requirements, and mark the details that are still undecided. We can review the information for quotation, but the coating limits, bonding requirements and acceptance tests need to be agreed before production is released.

Discuss Your ENEPIG PCB Requirements

Share your board files, finish specification and bonding requirements. We will review the coating, assembly interface and inspection scope with your team.