Skip to content
Sequential Lamination & Stacked Vias
Sequential Lamination Overview
Sequential lamination is a key process in advanced PCB manufacturing. It is commonly used for high-density interconnect (HDI) boards, allowing more layers, microvias, and connections in a compact design.
What Is Sequential Lamination?
Sequential lamination is a PCB manufacturing process used to build complex HDI boards. Copper and dielectric layers are added, laminated, drilled, and plated in multiple stages. This process supports microvias, higher layer counts, and dense interconnections within a compact PCB.
Sequential Lamination Process
Build the Base Structure
Begin with a PCB core or sub-laminate containing the initial copper layers and circuit patterns.
Drill and Plate
Drill precise holes through the structure and plate them with copper to create electrical connections between layers.
Add New Layers
Add dielectric material and copper foil to form the next layer of the PCB.
Laminate the Layers
Apply controlled heat and pressure to bond the new materials to the existing structure.
Form and Plate Vias
Drill or laser-form vias in the newly added layer, then plate them to establish the required connections.
Repeat the Cycle
Repeat the layering, lamination, drilling, and plating steps until the required layer count and interconnection structure are complete.
Benefits of Sequential Lamination
- Higher interconnection density: Supports complex routing and more electrical connections within a limited board area.
- Compact PCB designs: Enables microvias and fine-pitch features that reduce the space required for interconnections.
- Greater design flexibility: Allows designers to create complex HDI stack-ups for specific electrical and mechanical requirements.
Sequential Lamination Considerations
- Longer manufacturing time: Each lamination, drilling, plating, and alignment cycle adds time to the production process.
- Higher manufacturing cost: Multiple processing cycles and tighter registration requirements can increase production costs compared with standard multilayer PCB construction.
-
Stacked Vias Overview
Stacked vias are commonly used in HDI PCBs to create vertical electrical connections between multiple layers. By placing microvias directly above one another, they support higher routing density and more compact PCB designs.
What Is a Stacked Via?
A stacked via consists of two or more vias positioned directly above one another across multiple PCB layers. The vias are formed and copper-plated during sequential lamination to create a continuous vertical electrical connection.
Making a Stacked Via
Build the Base Structure
Begin with a PCB core or sub-laminate that contains the initial copper layers and plated connections.
Add the Dielectric and Copper
Add a dielectric layer and copper foil to the existing structure as part of the sequential lamination process.
Laminate the New Layer
Use controlled heat and pressure to bond the new dielectric and copper to the existing PCB structure.
Laser-Drill the Microvia
Use a laser to form a microvia in the newly added dielectric directly above the via below.
Plate and Repeat
Plate the microvia with copper to create the electrical connection. Repeat the cycle until the required stacked-via structure is complete.
Benefits of Stacked Vias
- Higher routing density: Stacked vias create vertical connections across multiple PCB layers, leaving more space for traces and components.
- Smaller PCB designs: Their compact structure supports fine-pitch components and dense HDI layouts without increasing the board size.
- Shorter connection paths: Direct vertical connections can reduce routing distances between layers and simplify complex interconnections.
Stacked Via Considerations
- Tighter alignment requirements: Each microvia must align accurately with the via above or below it to maintain a reliable electrical connection.
- More complex manufacturing: Stacked vias require sequential lamination, repeated drilling, copper plating, and careful process control.
- Higher production cost: Additional processing cycles and inspection requirements can increase costs compared with standard vias or staggered microvias.
- Note: Stacked vias are most suitable for compact HDI designs that require high routing density and fine-pitch component placement. Their use should be evaluated against the board’s space, reliability, and cost requirements.
Applications for Sequential Lamination and Stacked Vias
Sequential lamination and stacked vias are commonly used in compact, multilayer PCBs that require high routing density. Typical applications include:
- Telecommunications equipment: Supports dense routing, fine-pitch components, and complex multilayer connections.
- Aerospace electronics: Enables compact PCB layouts where space and weight are limited.
- Medical devices: Supports miniaturized electronics and high component density in space-constrained designs.
- Automotive electronics: Provides multilayer interconnections for compact control, sensing, and communication modules.
- Consumer electronics: Helps reduce PCB size while accommodating dense component layouts.
- Computing and data storage: Supports processors, memory devices, and other high-density interconnections.
- Energy systems: Enables compact control, monitoring, and power-management electronics.
Relationship Between Sequential Lamination and Stacked Vias
Sequential lamination and stacked vias are closely related, but they are not separate alternatives.
Sequential lamination is the manufacturing process used to add, drill, plate, and bond PCB layers in multiple cycles. It supports complex HDI structures, including blind vias, buried vias, and microvias.
Stacked vias are a specific via structure created during these lamination cycles. Two or more microvias are aligned vertically to form a direct connection across multiple layers.
In short, sequential lamination describes how the PCB is built, while stacked vias describe one of the interconnection structures that the process can produce.
Sequential Lamination and Stacked Via Support
Topline Circuit supports sequential lamination and stacked via structures for complex multilayer and HDI PCBs. Our engineering team reviews the stack-up, via structure, layer connections, materials, and manufacturing requirements before production. This helps identify design risks and confirm that the proposed structure is suitable for fabrication.
Your Sequential Lamination and Stacked Via Manufacturer
With more than 15 years of PCB manufacturing experience, Topline Circuit supports sequential lamination and stacked via structures for complex multilayer and HDI boards. Our services cover PCB fabrication, assembly, component sourcing, and engineering support, helping customers manage projects through one supplier.We review the stack-up, via structure, materials, and production requirements before manufacturing to reduce design risks and improve production reliability.
