Aluminum PCB Stack-Up

Define the circuit layers, insulating dielectric and aluminum structure for your board.

Choose the Structure Around the Circuit and Heat Path

We manufacture aluminum and metal-core PCBs for prototypes and production. Our aluminum PCB stack-up support covers copper layers, electrically insulating thermal dielectrics, metal-base selection, finished thickness and fabrication requirements.

Choose the structure around the circuit, heat source and mounting arrangement. We review the material schedule with your electrical isolation, thermal and mechanical requirements before production.

Single Circuit Layer on an Aluminum Base

A common insulated metal substrate (IMS) has one patterned copper circuit layer, an electrically insulating and thermally conductive dielectric, and an aluminum base.

The copper carries the circuit. Heat passes through the dielectric into the metal base, which spreads it toward the mounting surface or cooling assembly. Specify the contact interface as part of the complete thermal path.

These three main constituents do not make a three-circuit-layer PCB. Solder mask and pad finish are additional local treatments, defined separately from the principal dielectric.

Single-circuit-layer aluminum PCB section with copper above an electrically insulating thermal dielectric and aluminum base
Two copper circuit layers above an aluminum base, with separate interlayer and metal-isolation dielectric

Two Circuit Layers Above an Aluminum Base

This structure places two copper circuit layers on the same side of an aluminum base. The interlayer dielectric separates the circuits, while the base-isolation dielectric separates the lower circuit from the metal.

It provides additional routing capacity on the circuit side. Review the layer connections and every material between the heat-generating component and the aluminum.

Specify which holes connect the circuit layers and which approach or penetrate the base. Two circuit layers above a base are a different construction from circuits on opposite faces of a central metal core.

Circuit Layers on Both Sides of an Aluminum Core

A central aluminum core can carry insulated circuit structures on both faces. The example shows a copper circuit layer and electrical-isolation dielectric on each side of the metal.

Connections crossing the aluminum require an explicitly defined isolation structure unless an intentional connection to the metal is specified. A conventional plated hole through bare metal cannot be assumed to remain electrically isolated.

Review component access, mounting and heat removal from both faces. Define the copper, dielectric and finished thickness on each side in the fabrication drawing.

Aluminum-core PCB section with an insulating dielectric and copper circuit layer on each face of the central metal core

Specify Each Material and Finished Dimension

The material schedule should state both the electrical function and the thickness basis.

Circuit Copper

Specify the circuit-layer count, starting foil and finished copper requirement. Select the conductor geometry for current, allowable temperature rise and manufacturing requirements.

Insulating Thermal Dielectric

Identify the material grade, finished thickness and tolerance. Review thermal conductivity with its data source and test method, together with electrical and temperature requirements.

Aluminum Base or Core

Specify the aluminum grade, thickness, flatness and machining requirements. Identify exposed metal surfaces and any intended chassis or grounding connection.

Outer Treatments

Define solder mask, pad finish and any permanent coating by location. State whether the finished-thickness measurement includes those treatments.

Define Base Thickness and Board Thickness Separately

A board thickness note should not leave the metal thickness or measurement location ambiguous.

Thickness Budget

List copper, dielectric, metal and relevant permanent outer layers. Use consistent units and distinguish supplied material values from finished requirements.

Local Measurements

Identify where the board is measured and whether the location includes copper, mask or exposed metal. Define tolerance and inspection requirements for critical fitting surfaces.

Mechanical Fit

Review the finished construction against mounting holes, connectors, clamping features and the available assembly envelope.

Evaluate the Complete Thermal Path

Material conductivity alone does not predict the operating temperature of the assembly.

Dielectric Thickness and Area

For a simple uniform conduction path, thermal resistance depends on thickness, conductivity and effective area. Copper patterns and heat spreading make the actual board more complex than a one-dimensional material calculation.

Interfaces and Cooling

Include the component attachment, board-to-housing interface, contact pressure and heat sink or enclosure. A metal base spreads heat but still needs a path to the surrounding environment.

Design Inputs and Validation

Provide dissipated power, heat-source footprint, operating duty, ambient conditions and allowable component temperatures. Agree on thermal validation for the assembled product.

Maintain Electrical Isolation from the Metal

Treat the aluminum as electrically conductive and define its intended potential.

Operating and Test Conditions

State the working voltage, required isolation test, test duration and relevant environmental conditions. A material breakdown value is not automatically a continuous working-voltage rating.

Dielectric and Edges

Review the selected dielectric and finished thickness with clearances at copper edges, metal exposures and mounting features. Solder mask is not a substitute for the principal IMS isolation layer.

Holes and Interconnections

Separate mechanical holes, circuit vias and intentional metal connections on the drawing. Define the insulation and clearances for any interconnect passing through the metal.

Plan Mounting and Mechanical Processing

The installation details affect both isolation and heat transfer.

Base Contact

Identify the area contacting the heat sink or housing, along with flatness and interface-material requirements. Review coatings or protective films that remain in the thermal contact area.

Holes, Edges and Profiles

Provide mounting details, slots, routing and edge-clearance requirements. Account for exposed metal, burr control and the required electrical separation.

Assembly and Handling

Specify the assembly process, component access and any panel or support needs. Review depanelization and handling with the metal thickness and finished outline.

Aluminum PCB Manufacturing Support

We support material and construction review from prototype orders to repeat production.

Structure Options

Single-circuit-layer IMS, multiple circuit layers above a metal base and insulated structures on opposite faces of a metal core, selected for the project.

Copper and Materials

Standard and custom copper, dielectric and aluminum requirements, with material selection and finished-thickness review.

Fabrication and Assembly

Fabrication, surface finish, electrical testing and assembly support. Define any additional isolation tests, inspection records and acceptance criteria before release.

Files for an Aluminum Stack-Up Review

Send the available design package and identify fixed requirements.

  • Gerber or ODB++ data, layer mapping and drill files
  • Stack-up proposal, material grades and substitution requirements
  • Copper, dielectric, aluminum and finished board thicknesses with tolerances
  • Working voltage, isolation-test requirements and intended metal potential
  • Power dissipation, heat-source locations and operating conditions
  • Mounting drawing, base contact area and cooling-interface details
  • Quantity, delivery target and inspection or reporting requirements
  • For assembly projects: BOM, placement data and assembly drawing

See our aluminum and metal-core PCB manufacturing services for the wider scope. Submit the design through our project enquiry page for a construction review and quotation.

Aluminum PCB Stack-Up FAQs

No. The single-circuit-layer structure shown has one patterned copper layer and three main material constituents. State the circuit-layer count separately from the physical material schedule. Add solder mask, pad finish and any other permanent treatments where they occur in the released construction.

That must be defined on the drawing. Specify the aluminum thickness and the finished board thickness separately, with tolerances and measurement locations. Include copper, dielectric and relevant permanent outer treatments in the finished-thickness requirement so the manufactured board fits the assembly.

Not necessarily. Compare the dielectric thickness, effective heat-transfer area, copper distribution and material data under comparable test conditions. Check the component attachment and the interface to the cooling assembly as well. Provide power and temperature limits so the complete heat path can be assessed.

A thinner option must still meet the electrical, thermal and manufacturing requirements. Provide the working voltage, required isolation test, environment and proposed material. Review the finished dielectric thickness and acceptance conditions together; do not select it from thermal conductivity alone.

Yes, with a construction designed for those holes. An electrically isolated plated interconnect needs clearance from the aluminum and an insulating structure around its barrel. Specify intentional metal connections separately, and distinguish circuit vias from mechanical mounting holes. Send the hole locations, connected layers and isolation requirements so the appropriate structure can be reviewed before release.

Sometimes, but the decision depends on the complete assembly. Compare power dissipation and component temperature limits with the board area, housing interface and ambient conditions. If the metal base and enclosure cannot remove enough heat, an additional cooling solution is still required. Validate the selected arrangement under the intended operating conditions.

Discuss Your Aluminum PCB Stack-Up

Send your circuit files, thermal requirements and mounting drawing. We will review the aluminum stack-up and manufacturing quotation with your team.